277v Dimmer Wiring - LED Wiring Options Some combinations and exceptions may not be shown. For the most up to date information, especially for projects involving dimming, step-dimming or customer-specified driver, please consult factory. WD_susp_wall_LED-78-76-74 0313 All luminaires are pre-wired to one end with quick-wire connectors.. 277V 120V Ground Dimmer Neutral Connection only with Electronic Low Voltage Dimmers LEDL ED LED Hot 120V Neutral Hot Neutral 277V Transformer Transformer with Dimmer / Switch on Primary Sample Wiring Diagram for Nora LED Diamond series Dimmer or Switch may be on the Primary (277V) OR Secondary (120V) side of the transformer. Ground 277V Dimmer. The A21 3-Wire Fluorescent Dimmer Module is designed to provide dimming of Strand 3-wire phase control dimming ballasts where two wires are used for hot and neutral, and a third wire carries the phase control signal..
Control wiring is used to communicate commands and other information between control devices in a lighting system. “Proper control wiring is like the nervous system in the human body,” said Ronald Bryce, national sales manager for PLC-Multipoint Inc., Everett, Wash.. industrial design, this dimmer provides a modern and consistent look to match most interior designs. The dimmers with full range linear slide dimming are rated for wattages up to 600W (@277V/AC) for dimmable LED/CFL and fluorescents as well as 1000W (@277V/AC). cooper wiring sut7-w - 120/277v triac based universal dimmer, white.
0-10V Dimming. The first and simplest electronic lighting control signaling system, low voltage 0-10V dimmers use a low voltage 0-10V DC signal connected to each LED power supply or Fluorescent ballast. At 0 Volts the device will dim to the minimum light level allowed by the dimming driver, and at 10 Volts the device will be operating at 100%.. Fluorescent Dimming with Tu-Wire TM Electronic Ballasts Slide-to-Off Dimmers SMALL CONTROL Single pole, 120V 5A NFTU-5A- Single pole, 277V 20 lamps NF-20-277-Note: Magnetic dimming ballasts generally cannot be effectively dimmed below 20% low end. For best performance and relia-. Dimmer is engineered to deliver reliable dimming performance when used with 8 Amps fluorescent lighting devices. It is used with Lutron three-wire line-voltage control electronic dimming ballasts namely Hi lume, Compact SE, Eco-10, eco system ballasts and Hi-lume LED..
C4-DIM1-Z Wireless Dimmer Specifications and Supported Fixtures This Control4® Wireless Dimmer operates as part of a Control4 home-automation system to enable intelligent lighting control. It installs in a standard wall box using conventional wiring standards, and communicates with other devices through a wireless RF (radio frequency) connection.. For 2-wire Powerline wiring, individually insulate (cap-off) all unused Violet & Gray leads as shown. BALLAST escent White Gray (-) To Additional Ballasts 2-wire Fluorescent Powerline Dimmer Black Powerline Control Specs: Specification-grade controls are available for 120V or 277V operation of controllable analog electronic fluorescent ballasts.. installation instructions warning: to be installed and/or used in accordance with appropriate electrical codes and regulations. warning: if you are not sure about any part of these instructions, consult a qualified electrician. warning: use this device only with copper or copper clad wire..
Lutron NTF-10-277 Nova T Fluorescent 3-Wire Dimmer Single-pole 277V 8A Slide-to-off Dimmer Lutron NTF-10-277 Nova T Fluorescent 3-Wire Dimmer Single-pole 277V 8A Slide-to-off Dimmer The Nova T slide dimmer features a thin profile and the durability contractors expect from Lutron.. Lutron Diva® 3-Way 1-Pole Preset dimmer in hot color, is rated at 120-277 Volt AC at 50/60 Hz. Satin finished preset dimmer has paddle actuator and offers On/Off action for adjusting the light level..